power steering kit

[hunterbynature]

check this out bedy lovers

Trade Me Motors > Car parts & accessories > Parts - Other makes > Steering
CF BEDFORD POWER STEERING
Start price: $2,200.00 No reserve  Closes: Wed 12 May, 6:32 pm Listing #: 288426571
Starting bid:  $Place BidAuto-bid
Buy Now:  $2,200Buy Now


POWER STEERING FITTED TO CF BEDFORD VANS CAMPERS ETC
ALL WORK CARRIED OUT IS DONE BY QUALIFIED ENGINEER
THIS PRICE IS + GST TO DRIVE IN TO MY W/SHOP AND DRIVE OUT COMPLETED
INCLUDED IN THIS COST IS THE FOLLOWING

REMOUNTED MODIFIED POWER STEERING RACK
MOUNTED POWER STEER PUMP AND PULLEY
NEW BELT FITTED
ALL HOSES AND FITTINGS
STEERING COLUMN MODIFIED
MODIFIED STEERING UNIVERSALS
BASIC WHEEL ALIGNMENT DONE

THIS PRICE IS BASED ON A VAN WITH A 350 CHEV MOTOR AND WILL VARY SLIGHTLY DEPENDANT ON YOUR MOTOR TYPE
Please read the questions and answers for this auction.
Buyer's checklist



Buyer must pick-up
Seller is located in Lower Hutt City, Wellington
Payment details

NZ bank deposit
Cash
About the seller

ajeng (384 )
100% positive feedback
Member since Mar 2005
Seller's other listings
Seller's feedback
Read our safe buying advice
Place the first bid

 No reserve

Start price:$2,200
Your bid:$
Auto-bid
Place bid
Buy Now

Buy Now for $2,200

Buy Now
Closes: Wed 12 May, 6:32 pm. This auction may auto-extend.
Questions and answers
Ask the seller a question
I'm planning to toss out the 2.3 and auto and fit a holden 202 and auto which I already have. Would the 202 be ok to deal with re the power steering? My Ph oh too one 470 triple 3 kurli (86 )  9:41 pm, Thu 6 May
Yes this engine setup is not a lot dissimilar to a chev v8 setup actually so u would be looking at the cost above 6:53 pm, Fri 7 May

does this include certification costs cheers h

[Bas NZ]

Steveo, my camper runs a Transit rack, but bet this the new black jumbo runs a VN Holden!!!. I know front mounted it woud turn the wrong way, but the guys who did the swap but in a transfer box 3/4 way down the steering column attached to the engine mount ofcourse this puts it back in the right direction for turning. Bas

[hunterbynature]

thats a cunning idea bas, must one of those transfer boxes they use on vans, i think busy mentioned it on another thread somewere, can you get a pic up of the transfer box bas cheers  stevo

[Rogue Trooper]

Have they lengthened the rack somehow also? I wouldn't have thought a standard VN rack would be long enough.

[Bas NZ]

Hi Stevo, yep will get a photo of it up, mate borrowed the van today as he needed a towbar, hasen't come back yet. Will ask David (busy) if he knows of these, as would be a good idea if needed to be replaced some time. Bas
Yes Rogue rack has been lengthened as per photo below. Bas

[hunterbynature]

geez bas i hope he brings it back mate, he might be enjoying it to much lol

[Bas NZ]

Stevo, its back !!!!!, will PM you tomorrow as wife calls. Bas

[Rogue Trooper]

Yes Rogue rack has been lengthened as per photo below. Bas

Seems like an awful lot of work when there are easier options out there although I suppose it's one way of ensuring you can maintain the factory standard wheel lock.

[Bas NZ]

Think they just had the whole VN car and used all the bits they needed, doesen't look like much in the photos, but the engineer work is A1, close to a factory fit if there were to be one. The turning is good, but think the Transit under the Camper is a little better, just need to remember to make the turns a little sooner than normal. 

[ShaneJ]

Is the rack it self actually lengthened? Or just the rods?