User Info
Who's Online
Recent Topics
Cf Bedford for sale by wendyh
[February 10, 2025, 05:29:09 AM]
Introductions by moose
[February 09, 2025, 06:58:40 PM]
CF 350 Breaks conversion by greasey monkey
[November 19, 2024, 10:28:23 PM]
Advise on raising the rear end of a CF350 Motorhome. About 3.5T by johnxb351
[August 09, 2024, 08:17:08 AM]
Sale of 1977 Bedford Motorhome by johnxb351
[August 06, 2024, 08:27:12 PM]
173 extractors by kylee dingo
[April 07, 2024, 02:55:17 PM]
lowering my bedford cf by Ratbox
[October 07, 2023, 07:59:56 PM]
Adjustable Upper Control Arms by Saville
[August 22, 2023, 11:35:43 AM]
202 red to 202 black Carby engine by johnxb351
[June 21, 2023, 06:33:35 PM]
CF CLUTCH PEDAL by johnxb351
[June 18, 2023, 02:58:15 PM]
|
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - ethyl
1
« on: July 06, 2014, 08:59:59 PM »
I am setting up a Tarago 5 spd, same bell housing and internals as Supra but has remote shifter
also have f150 LSD 3.73 ratio with studs set for Mazda 4WD
2
« on: January 16, 2014, 07:43:53 PM »
I bought mine from England, they were on ebay there, bought 1/2 dozen steering rubber joints as well (same as Torana) were really cheap and arrived in 5 days
3
« on: December 01, 2013, 07:39:56 PM »
I have a modded 4 spd shifter to fit at the front and changed operation for reverse, It's in the shed some where at the farm.
I took the 4 spd out to fit toyota 5 spd. be up there Tuesday night if I remember could get a pic.
4
« on: November 04, 2013, 06:22:32 PM »
I would think any low wattage 12 volt light would be OK. the current from the globe is an exciter for the alternator
they will actually work without the light on the dash once the engine revs
5
« on: September 12, 2013, 07:27:09 PM »
why not a Holden 6 202 conversion? standard parts for that available.
6
« on: August 09, 2013, 07:31:32 PM »
that sounds like the old holden "rat trap"
no not rat trap, I have Toranas this a sheathed cable from the clutch pedal to push mechanism will try for pic tomorrow
7
« on: August 08, 2013, 08:08:38 PM »
the Tarago box is basically the same as Supra just diff housing but bit shorter
so I am using a Holden Supra bell housing, bought on ebay $156 used
front shaft is same as celica and supra I think
have 2 clutch mechanisms both cable from pedal to a lever system to push clutch fork
one was on the truck, don't know if original
the other from a Holden HZ 6
both bolt to the bell housing and the block
haven't look at which to use yet
would have liked a full cable but bell housing was to good to pass up
8
« on: August 02, 2013, 08:01:34 PM »
using a fuel injected black 202, will try for pic but only motor & box in just yet, still working on moving engine back
so haven't worked out where shifter will go
9
« on: August 01, 2013, 09:00:42 PM »
I am using a Tarago 5 spd which is similar to the supra box but has external gear shift levers and uses a remote shifter set with teleflex cables
that way I can mount the gear stick were I like
10
« on: June 27, 2013, 08:39:07 PM »
I have a rear set of Disks as well but not finished yet
again with matching 6 studs
will post pics when done
|
Guests: 375
Hidden: 0
Users: 0
Show Posts