User Info
Who's Online
Recent Topics
Cf Bedford for sale by wendyh
[February 10, 2025, 05:29:09 AM]
Introductions by moose
[February 09, 2025, 06:58:40 PM]
CF 350 Breaks conversion by greasey monkey
[November 19, 2024, 10:28:23 PM]
Advise on raising the rear end of a CF350 Motorhome. About 3.5T by johnxb351
[August 09, 2024, 08:17:08 AM]
Sale of 1977 Bedford Motorhome by johnxb351
[August 06, 2024, 08:27:12 PM]
173 extractors by kylee dingo
[April 07, 2024, 02:55:17 PM]
lowering my bedford cf by Ratbox
[October 07, 2023, 07:59:56 PM]
Adjustable Upper Control Arms by Saville
[August 22, 2023, 11:35:43 AM]
202 red to 202 black Carby engine by johnxb351
[June 21, 2023, 06:33:35 PM]
CF CLUTCH PEDAL by johnxb351
[June 18, 2023, 02:58:15 PM]
|
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - herb
1
« on: August 03, 2012, 10:32:52 AM »
has anyone had water entering the cab and wetting the floor mats near the wheel arch?think its comin in at the top of the guards where it meets the body,cause i run masking tape along there and it seem to fix it ,wat does anyone recommend to use ,can i seal between the top of the guard&the body?thanks in advance all.
2
« on: July 01, 2012, 01:10:59 PM »
Wanted cf bedford tow bar,wiper switch,light switch, wiper arms ,&blades,if not wat other switchers can be used? melb,thanks in advance all.
3
« on: December 08, 2010, 03:09:19 PM »
Hi all,I am looking for a tandem car trailer,does anyone know about the ones or seen them, were the axle is at the back no springs,and front axle rite at the front no springs and front wheels turn,they have arms and tie rods,just want to if the are safe to tow on the road ?if they can be registed in vic,thanks in advance all.
4
« on: April 21, 2010, 07:31:21 AM »
Can anyone tell me if a one toner diff will fit a cab/tray cf bedford?Also are the frontends all the same length wise?Do the tie rods go in the top of the steering arms or bottom?thanks all.
5
« on: April 12, 2010, 03:59:54 PM »
Yeah jimsvan thanks for ur reply,Iam interseted could you pm when ur ready sell the manual set up Iam only in noble park?also wat sump are u useing when u do the v8 conversion?
6
« on: April 02, 2010, 11:55:49 PM »
Hey jimsvan where abouts are you?Can you list what you got and how much? thanks for the reply.
7
« on: April 02, 2010, 11:46:03 PM »
Yeah Ben i want to go manual its has a 186 in it ,But would like to go with a 308 or 307 and aussie 4speed if someone has done it before and can tell me whats needed apart from motor and box?
8
« on: April 02, 2010, 11:24:44 PM »
Yeah thanks Ben.
9
« on: April 02, 2010, 12:59:38 PM »
Hi all looking for a manual clutch pedal set up for my old cf bedford if anyone can help me out?Or has anyone used a cable setup say from a vb,vc,commodore?thanks everyone.
10
« on: April 02, 2010, 12:20:43 PM »
Hi thanks for that George.
|
Guests: 171
Hidden: 0
Users: 0
Show Posts