BUGA Community

Technical => Driveline => Topic started by: vintageholden on August 12, 2016, 09:16:27 AM

Title: ecotec v6 into beddy
Post by: vintageholden on August 12, 2016, 09:16:27 AM: anyone know how to wire it up??
anyone here in w.a that can show me please..
Title: Re: ecotec v6 into beddy
Post by: vintageholden on August 17, 2016, 01:11:23 PM: not 1 person ?????????
Title: Re: ecotec v6 into beddy
Post by: BusyKiwi on August 18, 2016, 05:38:09 AM: I think most people use the complete loom
Title: Re: ecotec v6 into beddy
Post by: vintageholden on August 18, 2016, 01:29:51 PM: thanks mate..was wondering if anyone reads adds........
Title: Re: ecotec v6 into beddy
Post by: Merlin on August 19, 2016, 10:33:44 PM: you're better off running the VN harness and the T700 tranny as it doesn't run a BCM and isn't interfaced with the dash .Its a much simpler swap to do as you only need power and a couple of relays I have a disc with the wiring diagrams for all the Comodes .Might be able to sort it for you Cheers Neil
Title: Re: ecotec v6 into beddy
Post by: vintageholden on August 20, 2016, 02:41:51 PM: thanks....was told I can get the computer remaped with the vats taken off..or security so it will start in any car without bcm or key..????
Title: Re: ecotec v6 into beddy
Post by: rumax on August 20, 2016, 10:52:25 PM: I am no expert, but thought the Vn/Vp was the engine/auto of choice, as the gearbox was not computer controlled, but the Vr onwards was... But I guess it's only really important if your running it behind a red 6
Title: Re: ecotec v6 into beddy
Post by: vintageholden on August 22, 2016, 03:14:30 PM: got an ecotec in the shed so I thought I would use it.....plus I prefer them to buick...
Title: Re: ecotec v6 into beddy
Post by: Hooter on August 24, 2016, 09:22:05 PM: I live in Perth, have a CF250, I do conversions, and can do wiring the ecotech in for you
The eco is a good choice and way better than old series 1 engine, and particularly if you are going to use eco 4L60e trans, as they are fully tuneable.
I do all the Kalmaker stuff, you may have seen the website, and also have ads on Gumtree for all Holden EFI wiring and tuning from VN to VF.....
I have memcals to suit with VATs turned off so you dont need body control module...

I am about to put a LS1 into my CF Camper, and just put the paperwork in yesterday for approval... hopefully.
if yours was a Holden 6, it is the same setup as HQ Holden, so most GM motors just bolt straight in if you have HQ adaptors, with no welding or cutting except to floor opening.
PM me for phone number
Title: Re: ecotec v6 into beddy
Post by: vintageholden on August 24, 2016, 10:00:48 PM: pm sent
Title: Re: ecotec v6 into beddy
Post by: Gunning on August 27, 2016, 04:01:06 PM: Pm sent
Title: Re: ecotec v6 into beddy
Post by: vintageholden on August 30, 2016, 04:11:39 PM: never got it............
Title: Re: ecotec v6 into beddy
Post by: Hooter on August 30, 2016, 04:20:41 PM: Vintage did you PM me??
I havent seen anything yet...
Title: Re: ecotec v6 into beddy
Post by: Gunning on August 30, 2016, 04:29:58 PM: Gday hooter, I also sent you a pm, it wasn't showing up in my sent messages area though
Title: Re: ecotec v6 into beddy
Post by: Hooter on September 01, 2016, 11:26:58 PM: I think I was successful in replying to those PMs.... did they show up... terribly cluncky...
Title: Re: ecotec v6 into beddy
Post by: Gunning on September 02, 2016, 03:53:38 AM: yeah thanks mate, got your message
Title: Re: ecotec v6 into beddy
Post by: vintageholden on December 27, 2016, 03:05:12 PM: pm sent to hooter....